Blue screen of death driver

If you still encounter the BSOD dxgkrnl. Here are the steps to follow to do this:. If the problem remains unresolved, move on to next solution below. Windows has an in-built tool known as System File Checker that checks the integrity of system files and replaces corrupt files with good cached versions.

The SFC commands needs to be executed from the elevated command prompt. Here are the steps to follow in order to do this. Check whether you are getting the dxgkrnl. If the problem persists, move on to the next solution. There is the possibility that SFC was not able to restore all corrupt system files and hence the issue remains unresolved. It is a command-line tool that is used to service Windows setup, Windows images, and the Windows Recovery environment.

Here are the steps you need to follow to do this. In the list of results, right-click cmd and select Run as administrator. Note- DISM commands can take around minutes to complete as it also checks the registry for any corruption.

You need to be patient and wait for the command operation to complete before performing the next step. Some users have also reported that removing the network card has resolved the error.

Network failure can be caused by the Network Adapter, which refers to some driver errors. After you have configured the device, you can use the Resources tab in Device Manager to configure resource settings on the Windows operating system. Windows cannot determine the settings for this device.

Consult the documentation that came with this device and use the Resource tab to set the configuration. Hardware configuration If the hardware configuration is not working, you should replace the new hardware. With the Windows installation media, you can repair your computer via the Advanced options which you have no access to currently. Of 0xE error course, there are other ways to try, including updating the device driver in Device Manager and running hardware diagnostics provided using the Windows built-in feature.

If the solutions above fail, continue to carry out these methods to cope with the problem. Yes No. Sorry this didn't help.

Thanks for your feedback. To isolate your concern, we recommend that you check this article on how to perform a clean boot in Windows. This helps eliminate software conflicts that occur when you install a program or an update. You may also determine what conflict is causing the issue by performing this method. Note: Please go through the section: How to reset the computer to start normally after clean boot troubleshooting to boot the computer in normal startup after fixing the issue.

I've tried every single steps and methods but still no fix yet. Could it be my hard disk drive that is causing the problem?

Maybe the amount of RAM used has exceeded to its max? I'm starting to get frustrated. There are still options that we can try to isolate your concern, we suggest that you run the System File Checker.

SFC scan is a utility in Windows that allow users to scan for corruptions in Windows system files and restore corrupted files. To do this, follow the steps below:.

We can analyze the minidumps if you make them available from the OneDrive or other file sharing sites such as MediaFire. If you have problems uploading the minidumps copy them to the Desktop or the Documents folder and upload them from there.

Have you added devices lately or updated drivers - be sure to check in Windows Updates to see if a driver was updated prior to this occurring. This could also be caused by a loose card or cable and even a weak power supply.

That error means a driver is not handling the power state properly. Maybe only one has an issue. If it still blue screens think Video Driver. See troubleshooter link above for my generic driver update methods. To learn about them, please read the following content.

Most Windows 10 Stop Errors emerge on boot, some of which could be fixed after a restart, but in most situations, you'll be stuck in restart loop and have to manually shut computer down. To fix this kind of Windows 10 Blue Screen of Death errors, please think about what actions you did right before the BSOD, and then undo the operation. If Windows 10 Blue Screen of Death appears after you are installing a Windows update, driver, or application, please uninstall it to see whether Windows can start as before.

View the following solutions and choose the most proper one. Solution 1: Windows boots successfully after restart. Then, you'll see the following interface:. Of course, you can double click the update to uninstall it. Please right click Start button windows and choose Device Manager to enter the following window:. Here, please find the device driver that needs installing, then right click it, choose Uninstall, and click OK to confirm uninstalling.

Then, Windows will uninstall the device driver. Then, right click the program, choose Uninstall , and click Yes to confirm uninstalling. After uninstalling the wrong Windows update, device driver, or program, you should be able to boot Windows. However, if you forget the name of update, driver, or software, just try uninstalling the most recent one by viewing its installation date.

Since Windows is unbootable under this situation, you need to uninstall Windows update, driver, or program in Safe Mode. Step 3: Once in Safe Mode, you can uninstall Windows update, software, and device driver by above steps. Action 1: Check your hardware devices to see whether they are connectedly properly. If they are not fully pushed into their slots, BSOD is very likely to emerge.